Add power device (battery + power-off) for lilygo-tdeck-max

Devices/lilygo-tdeck-max/CMakeLists.txt

@@ -3,5 +3,5 @@ file(GLOB_RECURSE SOURCE_FILES Source/*.c*)
 idf_component_register(
     SRCS ${SOURCE_FILES}
     INCLUDE_DIRS "Source"
-    REQUIRES Tactility GDEQ031T10 TCA8418 driver
+    REQUIRES Tactility GDEQ031T10 TCA8418 BQ27220 driver
 )

Devices/lilygo-tdeck-max/Source/Configuration.cpp

@@ -1,5 +1,8 @@
 #include "devices/Display.h"
 #include "devices/TdeckmaxKeyboard.h"
+#include "devices/TdeckmaxPower.h"
+
+#include <Bq27220.h>
 
 #include <Tactility/hal/Configuration.h>
 #include <tactility/check.h>
@@ -82,6 +85,12 @@ static DeviceVector createDevices() {
     devices.push_back(keypad);
     devices.push_back(std::make_shared<TdeckmaxKeyboard>(keypad));
 
+    // Battery metrics from the BQ27220 fuel gauge (0x55); power-off via the
+    // SY6970 charger (0x6A). Enables the launcher's power-off button.
+    auto gauge = std::make_shared<Bq27220>(i2c);
+    devices.push_back(gauge);
+    devices.push_back(std::make_shared<TdeckmaxPower>(gauge, i2c));
+
     return devices;
 }
 

Devices/lilygo-tdeck-max/Source/devices/TdeckmaxPower.cpp

@@ -0,0 +1,139 @@
+#include "TdeckmaxPower.h"
+
+#include <tactility/log.h>
+#include <tactility/drivers/i2c_controller.h>
+
+constexpr auto* TAG = "TdeckmaxPower";
+
+// SY6970 charger (newer T-Deck Max revisions; older boards use BQ25896 @ 0x6B).
+// Register map is BQ25896-compatible for everything used here (see NOTES.md).
+static constexpr uint8_t SY6970_ADDRESS = 0x6A;
+static constexpr uint8_t SY6970_REG_03 = 0x03; // bit4 CHG_CONFIG: charge enable
+static constexpr uint8_t SY6970_REG_04 = 0x04; // bits[6:0] ICHG: charge current, 64 mA/LSB
+static constexpr uint8_t SY6970_REG_06 = 0x06; // bits[7:2] VREG: charge voltage, 3840 mV + n*16 mV
+static constexpr uint8_t SY6970_REG_07 = 0x07; // bits[5:4] WATCHDOG: I2C watchdog timer
+static constexpr uint8_t SY6970_REG_09 = 0x09;
+static constexpr uint8_t SY6970_REG_0B = 0x0B; // read-only status
+static constexpr uint8_t SY6970_CHG_CONFIG = 1 << 4;
+static constexpr uint8_t SY6970_BATFET_DIS = 1 << 5; // Force BATFET off = ship mode
+
+static constexpr TickType_t I2C_TIMEOUT = pdMS_TO_TICKS(50);
+
+// Charge parameters from the vendor factory firmware (XPowersLib SY6970 init):
+// watchdog off, 4288 mV target, 1024 mA fast-charge current. The I2C watchdog
+// must be disabled first, otherwise the chip reverts custom register values to
+// defaults after the watchdog expires. Input current limit (REG00) is left at
+// the hardware PSEL/ILIM default. Non-fatal: charging still works on chip
+// defaults if any write fails.
+bool TdeckmaxPower::configureCharger() const {
+    if (i2c_controller_register8_reset_bits(i2c, SY6970_ADDRESS, SY6970_REG_07, 0x30, I2C_TIMEOUT) != ERROR_NONE) {
+        LOG_E(TAG, "Failed to disable SY6970 watchdog");
+        return false;
+    }
+
+    uint8_t reg06 = 0;
+    if (i2c_controller_register8_get(i2c, SY6970_ADDRESS, SY6970_REG_06, &reg06, I2C_TIMEOUT) != ERROR_NONE ||
+        i2c_controller_register8_set(i2c, SY6970_ADDRESS, SY6970_REG_06, (reg06 & 0x03) | (28 << 2), I2C_TIMEOUT) != ERROR_NONE) { // 3840 + 28*16 = 4288 mV
+        LOG_E(TAG, "Failed to set SY6970 charge voltage");
+        return false;
+    }
+
+    uint8_t reg04 = 0;
+    if (i2c_controller_register8_get(i2c, SY6970_ADDRESS, SY6970_REG_04, &reg04, I2C_TIMEOUT) != ERROR_NONE ||
+        i2c_controller_register8_set(i2c, SY6970_ADDRESS, SY6970_REG_04, (reg04 & 0x80) | 0x10, I2C_TIMEOUT) != ERROR_NONE) { // 16 * 64 = 1024 mA
+        LOG_E(TAG, "Failed to set SY6970 charge current");
+        return false;
+    }
+
+    LOG_I(TAG, "SY6970 configured: 4288 mV / 1024 mA, watchdog off");
+    return true;
+}
+
+bool TdeckmaxPower::isAllowedToCharge() const {
+    uint8_t reg03 = 0;
+    if (i2c_controller_register8_get(i2c, SY6970_ADDRESS, SY6970_REG_03, &reg03, I2C_TIMEOUT) != ERROR_NONE) {
+        return false;
+    }
+    return (reg03 & SY6970_CHG_CONFIG) != 0;
+}
+
+void TdeckmaxPower::setAllowedToCharge(bool canCharge) {
+    error_t result;
+    if (canCharge) {
+        result = i2c_controller_register8_set_bits(i2c, SY6970_ADDRESS, SY6970_REG_03, SY6970_CHG_CONFIG, I2C_TIMEOUT);
+    } else {
+        result = i2c_controller_register8_reset_bits(i2c, SY6970_ADDRESS, SY6970_REG_03, SY6970_CHG_CONFIG, I2C_TIMEOUT);
+    }
+    if (result != ERROR_NONE) {
+        LOG_E(TAG, "Failed to set SY6970 charge enable");
+    }
+}
+
+bool TdeckmaxPower::supportsMetric(MetricType type) const {
+    switch (type) {
+        using enum MetricType;
+        case IsCharging:
+        case Current:
+        case BatteryVoltage:
+        case ChargeLevel:
+            return true;
+        default:
+            return false;
+    }
+}
+
+bool TdeckmaxPower::getMetric(MetricType type, MetricData& data) {
+    uint16_t u16 = 0;
+    int16_t s16 = 0;
+    switch (type) {
+        using enum MetricType;
+        case IsCharging: {
+            // REG0B CHRG_STAT bits[4:3]: 0 = not charging, 1 = pre-charge,
+            // 2 = fast charge, 3 = charge done. Only 1|2 count as charging —
+            // "done" must not (XPowersLib had this inverted once). Fall back to
+            // the fuel gauge's discharge flag if the charger doesn't answer.
+            uint8_t reg0b = 0;
+            if (i2c_controller_register8_get(i2c, SY6970_ADDRESS, SY6970_REG_0B, &reg0b, I2C_TIMEOUT) == ERROR_NONE) {
+                uint8_t charge_status = (reg0b >> 3) & 0x03;
+                data.valueAsBool = charge_status == 1 || charge_status == 2;
+                return true;
+            }
+            Bq27220::BatteryStatus status;
+            if (gauge->getBatteryStatus(status)) {
+                data.valueAsBool = !status.reg.DSG;
+                return true;
+            }
+            return false;
+        }
+        case Current:
+            if (gauge->getCurrent(s16)) {
+                data.valueAsInt32 = s16;
+                return true;
+            }
+            return false;
+        case BatteryVoltage:
+            if (gauge->getVoltage(u16)) {
+                data.valueAsUint32 = u16;
+                return true;
+            }
+            return false;
+        case ChargeLevel:
+            if (gauge->getStateOfCharge(u16)) {
+                data.valueAsUint8 = u16;
+                return true;
+            }
+            return false;
+        default:
+            return false;
+    }
+}
+
+void TdeckmaxPower::powerOff() {
+    // Ship mode: force the charger's BATFET off (REG09 bit5). Mirrors the vendor
+    // XPowersLib PowersSY6970::shutdown(). Note: this only fully powers the board
+    // down when running on battery with USB unplugged.
+    LOG_I(TAG, "Power off (SY6970 BATFET_DIS)");
+    if (i2c_controller_register8_set_bits(i2c, SY6970_ADDRESS, SY6970_REG_09, SY6970_BATFET_DIS, pdMS_TO_TICKS(50)) != ERROR_NONE) {
+        LOG_E(TAG, "Failed to write SY6970 shutdown register");
+    }
+}

Devices/lilygo-tdeck-max/Source/devices/TdeckmaxPower.h

@@ -0,0 +1,42 @@
+#pragma once
+
+#include "Tactility/hal/power/PowerDevice.h"
+
+#include <Bq27220.h>
+#include <tactility/device.h>
+
+#include <memory>
+
+using tt::hal::power::PowerDevice;
+
+// Power device for the LilyGO T-Deck Max. Battery metrics come from the BQ27220
+// fuel gauge (I2C 0x55); charging status, charge control and power-off (ship
+// mode, REG09 BATFET_DIS) use the SY6970 charger. Newer T-Deck Max revisions
+// ship the SY6970 (0x6A) instead of the older BQ25896 (0x6B); this board has
+// the SY6970 (confirmed by I2C scan). The two are register-compatible for
+// everything used here.
+class TdeckmaxPower final : public PowerDevice {
+    std::shared_ptr<Bq27220> gauge;
+    ::Device* i2c; // i2c0 controller, used to reach the SY6970 charger
+
+    bool configureCharger() const;
+
+public:
+
+    TdeckmaxPower(const std::shared_ptr<Bq27220>& gauge, ::Device* i2c) : gauge(gauge), i2c(i2c) {
+        configureCharger();
+    }
+
+    std::string getName() const final { return "T-Deck Max Power"; }
+    std::string getDescription() const final { return "Battery metrics (BQ27220), SY6970 charging and power-off"; }
+
+    bool supportsMetric(MetricType type) const override;
+    bool getMetric(MetricType type, MetricData& data) override;
+
+    bool supportsChargeControl() const override { return true; }
+    bool isAllowedToCharge() const override;
+    void setAllowedToCharge(bool canCharge) override;
+
+    bool supportsPowerOff() const override { return true; }
+    void powerOff() override;
+};